QF Ball Joint


The QF Ball Joints allow for up to 22° of movement off center. This makes a good fit for systems that have machines with moving dust ports. They are manufactured with Galvanized Steel only, in 4 to 14” diameter, 20, 18, 16, 14ga., and in lengths of 4.5 to 17.5”, all based on the diameter.
Login or Create an Account to get Pricing for this part and to Build a Bill of Material List for your Ducting project.
The Quick Fit Ball Joints allow for up to 22 degrees of movement off center. This makes a good fit for systems that have machines with moving dust ports.
QF Ball Joints are manufactured as follows:
- In 4 to 14 inch diameters, with 20, 18, 16, or 14 gauge Galvanized Steel only and in lengths of 4.5 to 17.5 inches based on the diameter size.
- The Collars are located on the exterior side of each port and considered as air flow non-directional and have a laser welded longitudinal seam. A raised lap seam and spot weld are used for attaching the collar to the body and no caulking is used
- Standard QF ends can be changed to Raw with a defined ID dimension (RawID), Raw with a defined OD dimension (RawOD), No Fitting or just a raw end (NoFit), Flexible hose adapter (RawFlex), Flat Flange (FFL), Angle Flange (ANGFL), or Van Stone (VanStone).
Size
in. |
Galvanized
ga. |
Weight
lbs. |
Length (L)
in. |
---|---|---|---|
4 | 20 | 2.10 | 9.50 |
6 | 20 | 3.85 | 11.75 |
8 | 18 | 5.00 | 14.00 |
10 | 18 | 8.95 | 14.25 |
12 | 16 | 9.25 | 15.25 |
14 | 14 | 15.70 | 17.50 |
Galvanized Gauge Metal Thickness
Gauge | Inches | Millimeters |
---|---|---|
20 | 0.0396 | 1.01 |
18 | 0.0516 | 1.31 |
16 | 0.0635 | 1.61 |
14 | 0.0785 | 1.99 |

NOTES:
- At temperatures ranging between 390° F and 480° F, the zinc-iron alloy layers in the galvanized steel will continue to provide a high level of protection from corrosion. However, there may be some peeling, changes in mechanical properties, and reduction in the corrosion protection. Recommended maximum service temperature is 390° F.
- Rock River Silicone Sealant and Red Devil HVAC/R High Temperature Silicone Sealant are not able to be painted.
Item | Material | Compliance/Rating |
---|---|---|
QF Ball Joint | Galvanized | ASTM A653 with a G-90 Rating |
304 SS | Finish meets ASTM A240 | |
316 SS | Finish meets ASTM A240 | |
3M Scotch Seal Metal Sealant 2084 | Acetone blend | AAMA Specification 801.1 |
Rock River Silicone Sealant | 100% Silicone | ASTM C920 Class 25 TT-S-00230C Class A and TT-S-001543A FDA No. 421 CFR 117.2600, conforms to FDA requirements |
Red Devil HVAC/R High Temperature Silicone Sealant | Silicone | ASTM C920 Class 25 TT-S-00230C Class A and TT-S-001543A CEBTP 432.6 140-2 Mil Spec 46106A CGSB 19C9-9B DIN 18540 Part 2 OREX 150031-2 |